|
other jobs:
Abu Dhabi
Bahrain
Oman
Saudi
Taiwan
Project:
Abu Dhabi
Department: Heavy Section Mill (HSM)
|
No |
Job Trade |
Nos. |
Salary (US$) /
month |
Experiences
( Years ) |
|
144 |
Process
Engineer |
1 |
4054 – 5539 |
|
|
145. |
Rolling
Process Shift Supervisor |
4 |
3570 - 4326 |
|
|
146. |
Furnace
Operator - Walking Beam |
4 |
2462 - 2900 |
|
|
147. |
Break Down
Mill Pulpit Operator |
4 |
2462 - 2900 |
|
|
148. |
Universal
Roughing/Finishing Mil (URF) Pulpit Operator |
4 |
2462 - 2900 |
|
|
149. |
Senior
Roller |
4 |
3158 - 3355 |
|
|
150. |
Finishing
Process Shift Supervisor |
4 |
3570 - 4326 |
|
|
151. |
Roller
Straightening (RSM) Operator |
4 |
2462 - 2900 |
|
|
152. |
Cold Saw
Operator |
4 |
2462 - 2900 |
|
|
153. |
Piling &
Despatch Operator |
8 |
2462 - 2900 |
|
|
154. |
Senior
Roll & Stand Guide Fitter |
4 |
3158 - 3355 |
5 - 10 |
|
155. |
Roll &
Stand Guide Fitter |
24 |
2462 - 2900 |
3 - 5 |
|
156. |
CNC
Supervisor |
1 |
3570 - 4326 |
5 - 10 |
|
157. |
CNC
Operator |
6 |
2462 - 2900 |
3 - 5 |
| |
|
|
|
|
|
|
TOTAL |
76 |
|
|
page <
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 >
JOB DESCRIPTIONS:
144.
Process
Engineer
Job Location Abu Dhabi
No. Of Vacancy: 1
The ideal candidate should have a
degree in Mechanical or Electromechanical Engineering, minimum 3
years working experience in a similar field & has experience in
the following Skills Requirement:
Deployment date is 1st Quarter of 2011.
145.
Rolling Process Shift Supervisor
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a degree in Mechanical Engineering,
minimum 5 years working experience in a similar field and has
experience in the following
Skills Requirement:
| 1. |
Actual
plant experience on similar equipment |
| 2. |
Experience
in supervisory level |
| 3. |
Experience
on Automated Roll Change Equipment |
| 4. |
Expert
knowledge of Section Mill adjustments for quality defect and
throughput
improvement on Reversing Mills
|
| 5. |
Familiarity
with roll designs and mill schedules for Section Mills |
| 6. |
Fully
understands the aspects of OEE (Operational Equipment
Effectiveness) affecting a
Rolling Mill
|
| 7. |
Sheet
Piling Experience |
| 8. |
Structural
Sections Mill - Beams, Angles or Rail Mill experience |
Deployment date is 2nd Quarter of 2011.
146.
Furnace
Operator - Walking Beam
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills
Requirement:
| 1. |
Check the
burner and furnace condition for correct flame / mix
|
| 2. |
Determine
root cause of poor furnace operation through analytical
interpretation of furnace
screens and data |
| 3. |
Ensure
accurate tracking and positioning of the pieces through
the furnace to discharge |
| 4. |
Experience
of operating a modern Walking Beam Furnace - Lift and carry the
beam in to
Furnace |
| 5. |
Feedstock
charge equipment to ensure optimal buffering and pacing for mill
operations
and
planned outages
|
| 6. |
Heavy
Structural Sections Mill experience |
| 7. |
Highly
automated plant equipment and modern Human Machine Interface
systems (HMI)
experience |
| 8. |
Maintain the
furnace temperatures and pacing to maintain beam blank
temperature
suitable for rolling
|
| 9. |
Monitor and
manage the furnace to ensure safe and stable operation
at all times. Shut down the furnace in a safe manner in emergency
conditions |
| 10. |
Monitor the
feedstock identity, characteristics and profile to
manage any discrepancies |
|
11. |
Planning and Scheduling to ensure best optimization of
available feedstock |
Deployment date is 3rd Quarter of 2011.
147.
Break Down Mill Pulpit Operator
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following Skills
Requirement:
| 1. |
Familiarity
with roll designs and BDM schedules for Section Mills |
| 2. |
Highly
automated plant equipment and modern Human Machine Interface
systems (HMI)
experience |
| 3. |
Strong
knowledge of quality defects and inspection procedures
for Structural Sections |
| 4. |
Experience
on Automated Roll Change Equipment |
| 5. |
Sheet Piling
Experience |
| 6. |
Heavy
Structural Sections Mill experience |
| 7. |
Manage the
BDM operational plant to ensure consistent product shape,
tolerances and
profiles to match the URF mill requirements
|
| 8. |
Monitor and
manage the Roll Change and Datum Set sequences |
| 9. |
Manage the
mill set-up, delivery and rolling practices to ensure a
cobble free operation |
| 10. |
Pace the BDM
mill and communicate upstream and downstream to ensure optimal operating
conditions |
| 11. |
Monitor and
manage the mill set-up, roll-wear, design and gap parameters to
ensure
defects free net-shapes to the URF |
| 12. |
Monitor and
manage the cropping strategies to ensure maximum yield and max
run-out
lengths are not exceeded at the URF
|
| 13. |
Monitor the
feedstock identity and profile and manage any discrepancies. and
ensure
accurate tracking of the pieces through the BDM to URF
|
| 14. |
Determine
root cause of poor BDM operation, roll designs and schedules
through analytical
interpretation of BDM screens, data and liaison with others
|
| 15. |
Experience of operating a
modern
reversing Break-down or Roughing Mill on a Sections or Rail Mill |
Deployment date is 3rd Quarter of 2011.
148.
Universal Roughing/Finishing Mill Pulpit Operator
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills
Requirement:
| 1. |
Experience of operating a
modern reversing Universal Roughing or Finishing Mill
|
| 2. |
Constantly monitor, pace
and communicate accordingly to mill pulpits and
personnel to ensure optimal operational conditions |
| 3. |
Expert knowledge of
Section Mill adjustments for quality defect and
throughput improvement on Reversing Mills |
| 4. |
Highly automated plant
equipment and modern Human Machine Interface systems (HMI) experience |
| 5. |
Experience on Automated
Roll Change Equipment |
| 6. |
Manage the URF operational plant to ensure consistent product
tolerances, delivery and defect free product to match customer
requirements |
| 7. |
Monitor and manage the
Roll Change and Datum Set sequences |
| 8. |
Manage the mill set-up,
delivery and rolling practices to ensure a cobble free
operation. |
| 9. |
Skilled at trimming and
controlling the section dimensions and profile |
| 10. |
Pace the URF mill and communicate upstream and downstream to
ensure optimal operating conditions |
| 11 |
Sheet Piling Experience |
| 12. |
Monitor and manage the
mill set-up, roll-wear, design and gap parameters to
ensure defect free product |
| 13. |
Able to determine root
cause of poor URF operation and
dimensional, roll designs and schedules through analytical
interpretation of URF screen |
Deployment date is 3rd Quarter of 2011.
149.
Senior
Roller
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills Requirement:
| 1. |
Actual plant experience
in a similar role |
| 2. |
Fully understands the
aspects of OEE (Operational Equipment Effectiveness)
affecting a Rolling Mill |
| 3. |
Familiarity with roll
designs and mill schedules for Section Mills |
| 4. |
Expert knowledge of
Section Mill adjustments for quality defect and
throughput improvement on Reversing Mills |
| 5. |
Experience in Structural
Sections Mill - Beams, Angles |
| 6. |
Sheet Piling experience |
Deployment date is 2nd Quarter of 2011.
150.
Finishing
Process Shift Supervisor
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma in Mechanical Engineering,
minimum 3 years working experience in a similar field and has
experience in the following
Skills Requirement:
| 1. |
Actual plant experience
on similar equipment - especially Roller Straightener,
Cut-to-Length and Piling Banks |
| 2. |
Experience in Structural
Sections Mill - Beams, Angles |
| 3. |
Strong knowledge of
quality defects and inspection procedures for Structural
Sections |
| 4. |
Fully understands the
aspects of OEE (Operational Equipment Effectiveness)
affecting a Rolling Mill Finishing End (Circa 500 pieces
/ hr) |
| 5. |
Sheet Piling experience |
Deployment date is 2nd Quarter of 2011.
151.
Roller
Straightening (RSM) Operator
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills Requirement:
| 1. |
Experience in operating
a modern Sections Roller Straightener Machine |
| 2. |
Experience in Structural
Sections Mill - Beams, Angles |
| 3. |
Fully understands the
aspects of OEE (Operational Equipment Effectiveness)
affecting a Rolling Mill Finishing End (Circa 500 pieces
/ hr) |
| 4. |
Knowledge of quality
defects and inspection procedures for Structural
Sections |
| 5. |
Effectively operate and
pace the Hotsaw, Cooling Bank and RSM to meet the
critical components of length, temperature and
Straightness |
| 6. |
Constantly monitor, pace
and communicate accordingly to mill pulpits and
personnel to ensure optimal operational conditions |
| 7. |
Effectively plan and
manage Blade and Section Roll Change sequences and other
delays / interventions |
| 8. |
Manage the operational,
control and adjust the plant to ensure consistent
product quality, throughput and defect free product to
match customer requirements |
| 9. |
Manage the cooling bank
optimisation and strategies to ensure minimal
straightness and thermal variance |
| 10. |
Manage the process
set-up, delivery and operating practices to ensure a
cobble free operation |
| 11. |
Monitor and ensure
accurate tracking of the pieces through the Hotsaw to
Cold Saws |
Deployment date is 3rd Quarter of 2011.
152.
Cold Saw
Operator
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 4 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills Requirement:
| 1. |
Experience in Structural
Sections Mill - Beams, Angles |
| 2. |
Experience in operating
a modern saw based Cut-to-Length optimization equipment |
| 3. |
Knowledge of quality
defects and inspection procedures for Structural
Sections |
| 4. |
Fully understands the
aspects of OEE (Operational Equipment Effectiveness)
affecting a Rolling Mill Finishing End (Circa 500 pieces
/ hr) |
| 5. |
Effectively plan and
manage Blade Change and Crop emptying sequences and
other delays / interventions |
| 6. |
Manage the operational
plant to ensure consistent product quality, throughput
and defect free product to match customer requirements |
| 7. |
Manage the CTL
optimization and strategies to ensure good throughput,
flow and minimal stock generation |
| 8. |
Monitor and manage the
blade cooling, cutting and change strategies to ensure
optimal blade life |
| 9. |
Pace the operations and
communicate upstream and downstream to ensure optimal
operating conditions |
| 10. |
Monitor and ensure
accurate tracking of the pieces through the Cold Saws to
Piling area |
| 11. |
Determine root cause of
poor equipment operation and set-ups through analytical
interpretation of available screens |
Deployment date is 3rd Quarter of 2011.
153.
Piling &
Despatch Operator
|
Job Location |
: Abu Dhabi |
Date Posted |
: 11/1/2010
|
|
No. Of
Vacancy |
: 8 |
Closing
Date |
: 10/1/2011 |
The ideal
candidate should have a Diploma or Technical Education, minimum
3 years working experience in a similar field and has experience
in the following
Skills Requirement:
| 1. |
Experience in Structural
Sections Mill - Beams, Angles |
| 2. |
Experience of operating
a modern Sections Piling Bank Equipment, Bundling,
Labelling and Despatch Equipment |
| 3. |
Knowledge
of quality defects and inspection procedures for
Structural Sections |
| 4. |
Fully understands the
aspects of OEE (Operational Equipment Effectiveness)
affecting a Rolling Mill Finishing End (Circa 500 pieces
/ hr) |
| 5. |
Sheet Piling experience |
| 6. |
Effectively operate and
pace the Piling and Despatch area to meet the critical
components of Pack configuration, Labelling accuracy,
order build |
| 7. |
Constantly monitor, pace
and communicate accordingly to mill pulpits and
personnel to ensure optimal operational conditions |
| 8. |
Effectively plan and
manage Piling equipment set-up, labeling and banding
supplies, change-over sequences and other delays /
interventions |
| 9. |
Manage the routing and
order batching optimization and strategies to ensure
good throughput, flow and minimal stock generation |
| 10. |
Monitor and ensure
accurate tracking of the pieces through the Piling Area
to Finish Product Bay |
| 11. |
Monitor and Manage the
Quality Inspection and Re-work / Gag-Press interfaces
and ‘feed-through’ requirements |
| 12. |
Determine root cause of
poor equipment operation and set-ups through analytical
interpretation of available screens |
Deployment date is 3rd Quarter of 2011.
154.
Senior Roll, Stand & Guide Fitter
The
ideal candidate should have a Diploma or Technical
Education, minimum 5 years working experience in a
similar field and has experience in the following
Skills Requirement:
1. Experience in Structural Sections Mill - Beams,
Angles
2. Actual plant experience on similar large mill Stand
and Guide equipment
3. Actual plant experience on Automated Roll Change
Equipment
4. Knowledge of quality defects and inspection
procedures for Structural Sections
5. Basic Section Mill Roll Workshop experience
|
144. Senior Roll, Stand &
Guide Fitter |
Vacancy - 4 |
|
Musts |
Preferred experience |
Dislikes |
|
5+ years actual
plant experience on similar large mill Stand and Guide
Equipment. |
Heavy Structural
Sections |
Only - Re-bar,
wire-rod experience. |
|
5+ years actual
plant experience on Automated Roll Change Equipment |
Strong English
communication skills |
|
Strong knowledge
of quality defects and inspection procedures for
Structural Sections. |
Plate or Flat Mill
experience |
|
|
5+ years in
Structural Sections Mill - Beams, Angles. |
|
|
|
Strong experience
in assembly and disassembly of Roll Stand and Guide. |
Educational
Qualifications |
|
|
Good English
Language competencies in listening, speaking and
understanding |
Diploma in
Mechanical Engineering |
|
155. Roll and Stand & Guide Fitter
The ideal candidate
should have a Diploma or Technical Education, minimum 3
years working experience in a similar field and has
experience in the following
Skills Requirement:
1. Experience in Structural Sections Mill - Beams,
Angles
2. Actual plant experience on similar large mill Stand
and Guide equipment
3. Actual plant experience on Automated Roll Change
Equipment
4. Knowledge of quality defects and inspection
procedures for Structural Sections
5. Basic Section Mill Roll Workshop experience
|
145. Roll and Stand &
Guide Fitter |
Vacancy - 24 |
|
Musts |
Preferred experience |
Dislikes |
|
3+ years actual
plant experience on similar large mill Stand and Guide
Equipment. |
Heavy Structural
Sections |
Only - Re-bar,
wire-rod experience. |
|
3+ years actual
plant experience on Automated Roll Change Equipment |
Strong English
communication skills |
|
Strong knowledge
of quality defects and inspection procedures for
Structural Sections. |
Strong experience
in assembly and disassembly of Roll Stand and Guide. |
|
|
5+ years in
Structural Sections Mill - Beams, Angles. |
Educational
Qualifications |
|
|
Good English
Language competencies in listening, speaking and
understanding |
Diploma in
Mechanical Engineering |
|
156. CNC Supervisor
The ideal candidate
should have a degree in Mechanical Engineering, minimum
5 years working experience in a similar field and has
experience in the following
Skills Requirement:
1. Experience in Structural Sections Mill - Beams,
Angles
2. Actual turning experience on modern CNC large lathes
on profiles Section Mill Rolls
3. Knowledge of roll designs and BDM schedules for
Section Mills
4. Programming experience on CNC/CAD/CAM systems
5. Sheet Piling experience
|
146. CNC Supervisor |
Vacancy - 1 |
|
Musts |
Preferred experience |
Dislikes |
|
5+ years in
Structural Sections Mill - Beams, Angles. |
Sheet Piling
experience |
Only - small CNC
lathe experience or non-CNC |
|
Basic knowledge of
roll designs and BDM schedules for Section Mills. |
Strong English
communication skills |
|
3+ years actual
turning experience on modern CNC large lathes on
profiles Section Mill Rolls |
Heavy Structural
Sections |
|
|
3+ years
programming experience on CNC/CAD/CAM systems. |
Educational
Qualifications |
|
|
Good English
Language competencies in reading and comprehension,
report writing, listening, speaking & understanding. |
Degree in
Mechanical Engineering with CAD or CAM certification. |
|
157. CNC Operator
The ideal candidate
should have a Diploma or Technical Education, minimum 3
years working experience in a similar field and has
experience in the following
Skills Requirement:
1. Experience in Structural Sections Mill - Beams,
Angles
2. Actual turning experience on modern CNC large lathes
on profiles Section Mill Rolls
3. Knowledge of roll designs and BDM schedules for
Section Mills
4. Programming experience on CNC/CAD/CAM systems
5. Sheet Piling experience
|
147. CNC Operator |
Vacancy - 6 |
|
Musts |
Preferred experience |
Dislikes |
|
5+ years in
Structural Sections Mill - Beams, Angles. |
Sheet Piling
experience |
Only - small CNC
lathe experience or non-CNC |
|
Basic knowledge of
roll designs and BDM schedules for Section Mills. |
Strong English
communication skills |
|
3+ years actual
turning experience on modern CNC large lathes on
profiles Section Mill Rolls |
3+ years
programming experience on CNC/CAD/CAM systems. |
|
|
|
Heavy Structural
Sections |
|
|
|
Educational
Qualifications |
|
|
|
Educational
qualification - Diploma / Technical Education with CAD
or CAM certification. |
|
Test Schedule*
|
Date |
Place |
Time |
|
Sunday & Monday,
May 1-2,
2011 |
HOTEL
MARBELA ANYER
Jl. Raya Karang Bolong Desa Cikoneng Anyer Kidul
P.O. Box 10Anyer 42466 Banten. |
08:00 - Finish |
|
|
|
|
* by
invitation only
page <
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 >
Terms & conditions:
|
1 |
Contract |
: |
3
years |
|
2 |
Probation period |
: |
6
months |
|
3 |
Working hours |
: |
40 hours / week |
|
4 |
Accommodation |
: |
Provided |
|
5 |
Medical insurance |
: |
Provided |
|
6 |
Life insurance |
: |
Provided |
|
7 |
Airfare |
: |
Provided, as contract |
|
8 |
Annual leave |
: |
25 working days |
| |
|
|
|
Interested
applicants are invited to submit detailed resume (CV) stating
personal particulars, employment history, qualifications in
English not latest by March 9, 2011 to the following e-mail
address :
esi@totaldata.co.id
in MS Word not more than 300kb.
Please write "
YOUR JOB CATEGORY”
on your application title and email subject.
Application with PDF or other format and exceeding
more than
300kb will not be considered.
We are sorry, only shortlist candidates will be notified.
page <
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1516 >
Last updated:
March 16, 2011
|
© 2000. Totaldata Persada. All rights
reserved. |
|
|
